Başlık için Ulaştırma Meslek Yüksekokulu listeleme
Toplam kayıt 32, listelenen: 1-20
-
The ballistic performance of aramid based fabrics impregnated with multi-phase shear thickening fluids
(Elsevier Sci LTD, 2017)Single-phase shear thickening fluids (STFs) have been extensively investigated in body protective applications. However, researchers do not have long-standing past experience of multi-phase STFs in protection. In the present ... -
A comparative investigation of the effects of concrete sleepers on the GPR signal for the assessment of railway ballast
(Institute of Electrical and Electronics Engineers Inc., 2018)This paper reports an investigation into the influence of concrete railway sleepers on the ground-penetrating radar (GPR) signal for the assessment of railway ballast. The main aim was to comprehend the effects of these ... -
A comparision between solar and wind energy according to different locations
(Sakarya University, 2016)In last year’s one of the most investigated issue is meeting electrical energy need from renewable energy sources. But sometimes it is difficult to decide which renewable energy source will be used. In this study two ... -
A computational study of cyclic thermal response of shape memory alloy thin-film island structures
(Springer Wien, 2017)With a view toward contributing to the state of the art in the research on shape memory alloy memory storage devices, the thermal response of a shape memory alloy (SMA) thin film during a complete cycle of heating and ... -
Değişken İlerleme Hızları Kullanılarak Tornalama İşleminde Talaş Kırma Uygulaması ile İlgili Yeni Bir Yaklaşım
(2017)Talaşlı imalat işlemlerinde, özellikle tornalama operasyonunda, işlem verimini ve ürün kalitesini belirleyen pek çok unsur mevcuttur. Kesme kuvvetleri, kesme bölgesi sıcaklığı, takım aşınması, üretilen talaş profili gibi ... -
Dynamic Properties of Clean Sand Modified with Granulated Rubber
(Hindawi LTD, 2018)Waste automobile tires are used as additives or replacements instead of traditional materials in civil engineering works. In geotechnical engineering, tires are shredded to certain sizes and mixed with soil, especially ... -
The effect of carbide particle additives on rheology of shear thickening fluids
(Korean Soc Rheology, 2016)In this paper, shear thickening fluids (STFs) including silicon carbide particles are presented. We fabricated a kind of STF based on nanosize fumed silica suspended in a liquid medium, polyethylene glycol, at a constant ... -
Effect of heat treatment on the bending behavior of aluminum alloy tubes
(Korean Soc Mechanical Engineers, 2017)Quasistatic experiments and numerical simulations were performed to investigate the three-point bending behavior of different temper AA6082 tubes in this study. The effect of heat treatment on the samples was investigated ... -
Effect of Riveting on the Joint Strength of Adhesively Bonded Double Lap Joints
(2018)The scope of this study is to determine the effectiveness of using rivets in the adhesive joints in order to combine plastic-based composite materials which are often used in today's engineering structures, to the joint ... -
The effect of silicon carbide additives on the stab resistance of shear thickening fluid treated fabrics
(Taylor & Francis Inc, 2017)Applications of shear thickening fluids (STFs) with ballistic fabrics improve the protection performance of body protective systems. This article presents an innovative view of STF-impregnated ballistic fabrics by integrating ... -
Effect of working fluid on the performance of the duplex Stirling refrigerator
(Elsevier Sci LTD, 2018)Duplex Stirling refrigerator is one of the best alternative systems for providing green and clean energy solutions. It consists of Stirling refrigerator and Stirling heat engine in a back to back configuration. The main ... -
The effects of cryogenic treatment on the toughness and tribological behaviors of eutectoid steel
(Korean Soc Mechanical Engineers, 2017)Cryogenic treatment is a supplementary heat treatment usually applied after quenching. Its effects are permanent and this process affects the entire section. There have been many studies related to cryogenic treatment, ... -
Empirical equations to estimate non-linear collapse of medium-length cylindrical shells with circular cutouts
(Elsevier Sci LTD, 2017)This paper examines the load bearing capacity of medium-length steel cylindrical shells with a circular cutout under the action of axial compression. Numerical simulations were performed for a radius-to-thickness ratio ... -
Experimental investigation of machining characteristics and chatter stability for Hastelloy-X with ultrasonic and hot turning
(Springer London LTD, 2018)Ultrasonic-assisted machining is a machining operation based on the intermittent cutting of material which is obtained through vibrations generated by an ultrasonic system. This method utilizes low-amplitude vibrations ... -
A GPR Spectral-Based Processing Method for Minimisation of Concrete Sleepers Effects in Railway Ballast Investigations
(Institute of Electrical and Electronics Engineers Inc., 2018)This paper investigates the influence of concrete railway sleepers on the ground-penetrating radar (GPR) signal for the assessment of railway ballast conditions. The main aim of this study is to propose a data processing ... -
High performance fabrics in body protective systems
(Trans Tech Publications Ltd, 2017)High performance fabrics are preferable for armor systems due to their lightweight structure and flexibility. High performance fabrics are generally used in body armor design for personal protection. However, these fabrics ... -
Investigation of impact behavior of TIG welded inconel 718 at aircraft engine operating temperatures
(Trans Tech Publications Ltd, 2017)In this work, Charpy notch pendulum impact test was performed on non-welded and TIG (Tungsten Inert Gas) welded Inconel 718 specimens at three different temperatures as 20°C, 500°C and 700°C. After the completion of tests, ... -
Multi response optimization of turning operation with self-propelled rotary tool
(Elsevier Science BV, 2015)The purpose of the study is to determine the cutting performance of self-propelled rotary tool (SPRT) in the turning operation of hardened EN24 steel by optimizing the cutting conditions. Parameters such as horizontal ... -
Overall performance of the duplex Stirling refrigerator
(Pergamon-Elsevier Science LTD, 2017)The duplex Stirling refrigerator is an integrated refrigerator consists of Stirling cycle engine and Stirling cycle refrigerator used for cooling. The equality of the work generation of the heat engine to the work consumption ...
