Yayın tarihi için Bildiri Koleksiyonu listeleme
Toplam kayıt 40, listelenen: 21-40
-
Effect of starting Si3N4 powder type and sintering conditions on the grain morphology of ?-SiAlON ceramics
(2002)Nitrogen rich neodymium-ytterbium containing multi-cation ?-sialon starting compositions have been prepared by gas pressure sintering using "conventional" ?-Si3N4 or plasma produced ß-Si3N4 powder. The effect of ?-SiAlON ... -
Mechanical properties of melt infiltrated boron carbide-aluminium composites
(Trans Tech Publications LTD, 2002)Boron carbide (B4C)-aluminium (Al) composites were produced by melt infiltration of 2024-T3 series Al alloys into porous B4C compacts in the temperature range of 985 degrees -1370 degreesC under an inert atmosphere (Ar). ... -
Transmission electron microscopy of SrO containing multi-cation doped ?-SiAlON ceramics
(2002)An advantage of ?-SiAlON is that it can accommodate cations of sintering additives and hence reduces the amount of deleterious remnant intergranular amorphous phase. However, it is believed that relatively large cations ... -
Preparation and fracture behavior of alumina platelet reinforced alumina-monazite composites
(Japan Inst Metals, 2002)Fracture behaviors were investigated in the laminated alumina composite ceramics. To improve the mechanical properties of alumina ceramics, templated grain growth (TGG) technique of alpha-Al2O3 platelet and LaPO4 as a ... -
Performance of new alpha-beta SiAlONs in turning operations
(Trans Tech Publications LTD, 2002)New alpha-beta SiAlON ceramics were produced, characterised and tested in turning operations of cast iron. Cutting speeds varied between 400-1200 m/min while feeding rates were between 0.3 to 0.5 mm/rev. The results were ... -
Capacitor discharge joining of silicon carbide based ceramics
(Trans Tech Publications LTD, 2002)A capacitor-discharge joining technique has been successfully used to join oxide ceramics using thin metal foils. In this study, silicon carbide (SiC) ceramic joints and silicon carbide-titanium diboride (TiB2) composite ... -
Chemical durability behaviour of bulk glasses in the SrO-Mn2O3-Fe2O3-MgO-ZrO2-SiO2 (SMFMZS) system
(Trans Tech Publications LTD, 2002)It is known that the SrO-MgO-ZrO2-SiO2 (SMZS) system glasses with 40 weight % silica content seem to give a very high chemical endurance against highly alkaline solutions and can be recommended for the reinforcement of ... -
Phase studies of reactive infiltrated boron carbide-aluminium composites by quantitative XRD
(Trans Tech Publications LTD, 2002)Fully dense (> 98 % of theoretical) boron carbide (B4C)-aluminium (Al) composites were produced between 985 degrees and 1370 degreesC by pressureless melt infiltration of Al alloys into porous B4C compacts under an argon ... -
Textured alumina ceramics by uniaxial pressing
(Trans Tech Publications LTD, 2002)Highly textured, dense alumina ceramics were fabricated by a processing route which utilizes a mixture of Al metal powder, alumina powder, alumina platelet (template) particles and a liquid phase former. The process involves ... -
Transmission electron microscopy of SrO containing multi-cation doped alpha-SiAlON ceramics
(Trans Tech Publications LTD, 2002)An advantage of alpha-SiAlON is that it can accommodate cations of sintering additives and hence reduces the amount of deleterious remnant intergranular amorphous phase. However, it is believed that relatively large cations ... -
Effects of different Si3N4 starting powders and sintering conditions on the grain morphology and mechanical properties of alpha-SiAlON ceramics
(Trans Tech Publications LTD, 2002)Nitrogen rich yttrium-cerium containing multi-cation alpha -SiAlON starting compositions have been prepared by gas pressure sintering using "conventional" alpha -Si3N4 or alpha-beta Si3N4 containing powder. The effect of ... -
Hydrothermal synthesis of tabular perovskite particles
(Trans Tech Publications LTD, 2002)Phase pure perovskite lead titanate and lead zirconate titanate powders were produced by hydrothermal synthesis. Reaction temperature and time are critical processing parameters for formation of phase-pure perovskite ... -
Improvement of elongated alpha-SiAlON ceramics by variation of the processing conditions and amounts of additives
(Trans Tech Publications LTD, 2002)Two types of Y-alpha -SiAlON composition, with different amounts of additional liquid phase were densified in a gas pressure sintering furnace using three different sintering cycles. One series of samples was heated up to ... -
Hydrothermal synthesis of lead titanate and lead zirconate titanate electroceramic particles
(Taylor & Francis LTD, 2003)Hydrothermal synthesis of two lead-based perovskite powder systems, lead titanate and lead zirconate titanate, was investigated. Phase-pure perovskite lead titanate and lead zirconate titanate with various morphologies ... -
The effect of different nucleation temperatures on the grain morphology of ?-SiAlON ceramics
(2003)Nitrogen rich yttrium-cerium containing multi-cation ?-SiAlON starting compositions were prepared by gas pressure sintering using conventional ?-Si3N4 powder. Microstructural characterization of the two stage sintered ... -
The effect of different nucleation temperatures on the grain morphology of alpha-SiAlON ceramics
(Trans Tech Publications LTD, 2003)Nitrogen rich yttrium-cerium containing multi-cation alpha-SiAlON starting compositions were prepared by gas pressure sintering using conventional alpha-Si3N4 powder. Microstructural characterization of the two stage ... -
The design of compositions for multi-cation doped ?-ß SiAlON ceramics by the Rietveld method
(2003)Although densification of ?-ß-SiAlON ceramics is easier by using sintering additives, it is difficult to achieve the designed composition and therefore the mechanical properties after sintering. This is mainly due to the ... -
Novel SiAlON ceramics for cutting tool applications
(Trans Tech Publications LTD, 2003)New alpha-beta SiAlON ceramics were produced in aqueous medium by Using Multiple oxides as densifying additives. The sintered materials were characterised using a combinations of techniques such as XRD, SEM and TEM. The ... -
The design of compositions for multi-cation doped alpha-beta SiAlON ceramics by the Rietveld method
(Trans Tech Publications LTD, 2003)Although densification of alpha-beta-SiAlON ceramics is easier by using sintering additives, it is difficult to achieve the designed composition and therefore the mechanical properties after sintering. This is mainly due ... -
Effect of the Chemical Composition on The Pyroplastic Deformation of Sanitaryware Porcelain Body
(IOP Publishing LTD, 2011)Pyroplastic deformation is the bending of a ceramic specimen caused by gravity during heat treatment. It can be defined as the loss of shape of product during its firing. Pyroplastic deformation is related to properties ...